kunci jawaban tes cisco

temen temen yang lagi tes cisco ni aq ada sedikit bocoran buat kalin,,,
mudah"an bisa membantu,,,

=>chapter 1
=>chapter 2
=>chapter 3
=>chapter 4
=>chapter 5
=>chapter 6
=>chapter 7
=>chapter 8
=>chapter 9
=>chapter 10
=>chapter 11
=>final exam
=>practice final exam

selamat mengerjakan tes yaw temen",,,,pasti bagus nilainya,,,,
sebenarnya aq dulu telat lo dapat cara ini,,,
aq sekarang berbaik hati pada temen" agar nilai kalian bagus n uangnya ga percuma bayar mahal"
tapi ga lulus tes cisco,,,kalian sebagai IT harus cerdik temen",,,intinya logika kalian jalan,,,
semangat anak IT,,,kalian bisa,,,,

kunci jawaban Practice Final Exam

1	Refer to the exhibit. Which set of devices contains only intermediary devices? A, B, D, G A, B, E, F C, D, G, I G, H, I, J

2	Which three IPv4 addresses represent a broadcast for a subnet? (Choose three.) 172.16.4.63 /26 172.16.4.129 /26 172.16.4.191 /26 172.16.4.51 /27 172.16.4.95 /27 172.16.4.221 /27

3

Refer to the exhibit. The diagram represents the process of sending email between clients. Select the list below that correctly identifies the component or protocol used at each numbered stage of the diagram. 1.MUA 2.MDA 3.MTA 4.SMTP 5.MTA 6.POP 7.MDA 8.MUA 1.MUA 2.POP 3.MDA 4.SMTP 5.MTA 6.MDA 7.SMTP 8.MUA 1.MUA 2.POP 3.SMTP 4.MDA 5.MTA 6.SMTP 7.POP 8.MUA 1.MDA 2.SMTP 3.MTA 4.SMTP 5.MTA 6.MUA 7.POP 8.MDA 1.MUA 2.SMTP 3.MTA 4.SMTP 5.MTA 6.MDA 7.POP 8.MUA

4	Which memory contents will change as a result of using the Router# erase startup-config command on a router? RAM ROM flash NVRAM

5	As network administrator, what is the subnet mask that allows 510 hosts given the IP address 172.30.0.0? 255.255.0.0 255.255.248.0 255.255.252.0 255.255.254.0 255.255.255.0 255.255.255.128

6	What are two characteristics of the data link layer? (Choose two.) It segments and reorders the data. It exchanges the frames between nodes. It defines the method by which network devices place data onto the media. It manages the transfer of data between the processes that run on each host. It retrieves signals from the media and restores them to their bit representations.

7	Which statement is true about the ICMP protocol? It is an application layer protocol. It is designed to make IP a reliable protocol. It is often filtered out of networks for security purposes. If a host does not respond to an ICMP echo request, the host is not functioning.

8	A user types the enable command. What task can be performed at the privileged EXEC mode? Configure the device. Configure individual interfaces. Configure individual terminal lines. Issue show and debug commands.

9	Which statement is true about router hostnames? A hostname should be unique on each router. A router hostname cannot contain capital letters. A router hostname is configured in privileged executive mode. A router hostname must be created before any other configurations can be added to the device.

10	Refer to the exhibit. At which OSI layer is serial interface 0/0/1 experiencing problems? Layer 1 Layer 2 Layer 3 Layer 4

11

What are three characteristics of CSMA/CD? (Choose three.) It monitors the media for presence of a data signal. After detecting a collision, hosts can resume transmission after a random timer has expired. A jam signal is used to ensure that all hosts are aware that a collision has occurred. Devices can be configured with a higher transmission priority. Data is transmitted only when the data signal is present. It uses a token system to avoid collisions.

12	If an administrator wished to return a router to the default state, what additional step must be taken after issuing the command erase start-up config? Reload the device. Issue the command copy running-config start-up config. Perform a show running-config to verify that the file was removed. Enter the interface commands to allow the device to connect to the network.

13	Which three statements are true about network layer addressing? (Choose three.) It uniquely identifies each host. It assists in forwarding packets across internetworks. It uses a logical 32-bit IPv4 address. It is not a configurable address. It is a physical address. It identifies the host from the first part of the address.

14	A network administrator wants to restrict access to the router privileged EXEC mode. Which password should the administrator use? enable aux console VTY

15	Refer to the exhibit. What is required on host A for a network technician to create the initial configuration on Router1? an FTP client a Telnet client a terminal emulation program a web browser

16	Refer to the exhibit. A user wants to access the Internet from the PC. A part of the running configuration of the router is shown. Which default gateway IP address should be configured at the PC to enable this access? 10.1.192.1 10.1.192.2 10.1.192.54 192.31.7.1

17	Refer to the exhibit. Host X is unable to communicate with host Y. Which command can be run at host X to determine which intermediary device is responsible for this failure? telnet 192.168.1.1 ping 192.168.1.1 ftp 192.168.1.1 tracert 192.168.1.1

18	Which device should be used for routing a packet to a remote network? access switch DHCP server hub router

19	What is the result of using the clock rate 56000 command at the serial interface of the router? The interface is configured as a DCE device. The interface timers are cleared. The FastEthernet interface is made to emulate a serial interface by assigning it a timing signal. The IP address for the serial interface is configured.

20

A network administrator is asked to design a new addressing scheme for a corporate network. There are 60 users in the main office, 40 users in the branch office, 28 users in manufacturing, 12 in the sales office, and 4 users in the research office. Which VLSM addressing scheme that uses the 192.168.88.0/24 network will fulfill the requirements while wasting the fewest addresses? 192.168.88.0/26 main 192.168.88.32/26 branch 192.168.88.64/26 manufacturing 192.168.88.96/27 sales 192.168.88.128/28 research 192.168.88.0/26 main 192.168.88.64/26 branch 192.168.88.128/27 manufacturing 192.168.88.160/28 sales 192.168.88.176/29 research 192.168.88.0/27 main 192.168.88.32/27 branch 192.168.88.64/28 manufacturing 192.168.88.80/29 sales 192.168.88.88/30 research 192.168.88.0/27 main 192.168.88.64/28 branch 192.168.88.80/28 manufacturing 192.168.88.96/29 sales 192.168.88.104/30 research

21

Refer to the exhibit. Host A wants to access the Internet. Which combination of a Layer 2 address and a Layer 3 address will enable this access from host A? Destination MAC: 0030.8596.DE83 Default gateway: 209.165.202.130 Destination MAC: 0030.8596.DE82 Default gateway: 172.16.9.2 Destination MAC: 0030.8517.44C4 Default gateway: 172.16.1.1 Destination MAC: 0030.8517.44C4 Default gateway: 209.165.202.130

22	Refer to the exhibit. Which two facts can be determined about the topology? (Choose two.) Four collision domains are present. One logical network is represented. Two broadcast domains are present. Three networks are needed. Three logical address ranges are required.

23	Which OSI layer uses the header information to reassemble the data segments into streams? application layer network layer presentation layer session layer transport layer

24	Refer to the exhibit. The PC, the routing table of which is displayed, is configured correctly. To which network device or interface does the IP address 192.168.1.254 belong? PC switch router interface fa0/0 router interface fa0/1

25	By using the ipconfig command, a network administrator determines that a workstation has the address 192.168.3.38 with 29 bits set in the subnet mask. To what network does the workstation belong? 192.168.3.8 192.168.3.16 192.168.3.24 192.168.3.32

26	Refer to the exhibit. The NAT functionality of the router is enabled to provide Internet access to the PC. However, the PC is still unable to access the Internet. Which IP address should be changed to 209.165.201.1 to enable the PC to access the Internet? 192.168.1.191 192.168.1.101 192.168.1.1 192.168.1.254

27

Refer to the exhibit. The serial interface of the router was configured with the use of the commands that are shown. The router cannot ping the router that is directly connected to interface serial 0/0/0. What should the network technician do to solve this problem? Configure the description at interface serial 0/0/0. Configure an IP address on interface serial 0/0/0. Remove the no shutdown command at interface serial 0/0/0 Reboot the router.

28	Refer to the exhibit. A network administrator is troubleshooting a link that is down between Router1 and Router2. To correct the problem, which wire pairs need to be switched on one of the Ethernet cable ends? pair 1 and pair 2 pair 1 and pair 3 pair 2 and pair 3 pair 2 and pair 4

29	Refer to the exhibit. Host B was powered off. What change will occur in the MAC table of the switch? The table will remain unaffected. The switch will remove the MAC address at Fa0/19. The switch will retain the MAC address until host B is powered on again. The switch will rebuild the MAC table by assigning the FFFF.FFFF.FFFF address to port Fa0/19.

30	A network technician is tasked with setting up a network for six users, but the users should be able to use their accounts to log on from any of the six computers. What type of network should be used? workgroup P2P applications peer-to-peer network client-server network

31

Examine the graphic with current configurations. Host A in the Clerical office failed and was replaced. Although a ping to 127.0.0.1 was successful, the replacement computer cannot access the company network. With proxy ARP disabled on the Fa0/0 interface of the New York router, what is the likely cause of the problem? network card failure network cables unplugged IP address incorrectly entered subnet mask incorrectly entered

32	Refer to the exhibit. An administrator on PC1 wants to view some HTML code from a web page housed on the web server. Which client application will allow this request to be started? ********************************

33	What is the Cisco IOS? system software for Cisco devices Read Only Memory in Cisco devices non-volatile storage for device configurations an initial operating system that is used for boot functions

34	Refer to the exhibit. A network technician has made several changes to R1 since the configuration has last been saved. The modified configuration did not produce the desired changes. The technician wants to store a backup copy of the saved configuration on a TFTP server before reloading. Which action will cause the unmodified data to be saved on the TFTP server? ***************************

35	Which physical connector type is used for a serial V.35 connection to the CSU/DSU? *******************************

36	Refer to the exhibit. Host A sends a frame to host C with a destination MAC address CC. The MAC address for host C is not in the MAC table of switch SW1. How will SW1 handle the frame? Switch SW1 will drop the frame. Switch SW1 will forward the frame to host C. Switch SW1 will flood the frame out all ports. Switch SW1 will flood the frame out all ports except port Fa0/1.

37	Refer to the exhibit. Which Layer 2 protocol could be used inside nework A and network C? IP TCP UDP Ethernet

38	The Layer 4 header contains which type of information to aid in the delivery of data? service port number host logical address device physical address virtual connection identifier

39	A network has grown too large for technicians to configure network addresses and hosts files for name resolution. Which two application layer services should be added to the server to allow these needs to be satisfied dynamically? (Choose two.) DNS FTP DHCP HTTP SMTP

40	Which OSI layer uses a connection-oriented protocol to ensure reliable delivery of data? application layer presentation layer session layer transport layer

41	Which fiber connector supports full-duplex Ethernet? ***************************************

42	Refer to the exhibit. The headers added at each layer are shown. Which layer adds the destination and source process numbers to ensure that data is delivered to the correct application? physical layer data link layer network layer transport layer

43	Refer to the exhibit. Which logical topology describes the exhibited network? star ring point-to-point multi-access

44	Refer to the exhibit. A technician uses the nslookup command on the PC and views the output that is displayed in the exhibit. What is the IP address of the primary domain name server used by the host? 10.10.10.32 192.168.1.5 192.168.1.99 192.168.2.100

45	While configuring a router, a network technician wants to name the router. Which prompt should the technician see when entering the hostname command? Router> Router# Router(config)# Router(config-line)#

46

Refer to the exhibit. The host was disconnected from switch 2 and connected to switch 1. Which combination of IP address, subnet mask, and default gateway should be assigned to this host to allow it to function in the network? IP address: 10.10.9.37 Subnet mask: 255.255.255.240 Default gateway: 10.10.9.35 IP address: 10.10.9.37 Subnet mask: 255.255.255.224 Default gateway: 10.10.9.35 IP address: 10.10.9.29 Subnet mask: 255.255.255.248 Default gateway: 10.10.9.35 IP address: 10.10.9.32 Subnet mask: 255.255.255.224 Default gateway: 10.10.9.35 IP address: 10.10.9.37 Subnet mask: 255.255.255.224 Default gateway: 196.1.105.6 IP address: 10.10.9.63 Subnet mask: 255.255.255.224 Default gateway: 10.10.9.35

47	Refer to the exhibit. Which option shows the correct topology given the configuration of Router1? ***********************************************************

48	Refer to the exhibit. A PC is connected to a network. Which action will verify that the PC can communicate with its default gateway? Use the ping 127.0.0.1 command. Use the ipconfig command. Use the ipconfig/all command. Use the ping 10.0.0.254 command.

49	What information is contained in the header of Layer 3 to help data delivery? port number device physical address destination host logical address virtual connection identifier

50

Refer to the exhibit. A web browser is running on host PC1 with an IP address 10.10.2.2/24. A dynamic port number of 49152 is assigned to the browser. The browser sends a request for a web page to the web server with an IP address 192.168.1.254/24. Which statement is true? The session is established using TCP, and the socket number for the web server is 192.168.1.254: 80. The session is established using TCP, and the socket number for the web server is 192.168.1.254: 49152. The session is established using UDP, and the socket number for the web server is 192.168.1.254: 80. The session is established using UDP, and the socket number for the web server is 192.168.1.254: 49152.

sumber  http://nont.myknw.com